Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.780 Overall Width: 1.1" Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw Red Dot Fitment: Trijicon RMR This mount will fit: Smith & Wesson M&P Full Size Smith & Wesson M&P 2.0 Full Size Smith & Wesson M&P 22 Full Size Smith & Wesson M&P Compact* Smith & Wesson M&P 2.0 Compact* Smith & Wesson SD9VE Smith & Wesson SD40VE This mount does not fit: Smith & Wesson M&P Shield (Our mount is too wide to fit the Shield) Smith & Wesson M&P Shield EZ .380 Smith & Wesson SW9VE Smith & Wesson SW40VE Smith & Wesson M&P C.O.R.E Series *Will not fit the M&P .22 Compact. Smith and Wesson's rear sight dovetails are known to vary in dimensions. Our sights are made to the same tolerances. Some users may have trouble installing our plate on their slide due to the varying tolerances in your slides. Please keep this in mind when ordering.These mounts should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs *Rear sight pusher tool highly recommended*
Kompakt och hållbar montagelösning för din Trijicon RMR
EGW:s S&W M&P TRIJICON RMR SIGHT MOUNT är en perfekt lösning för att montera din Trijicon RMR rödpunktsikte på din Smith & Wesson M&P pistol. Med en konstruktion av 7075 aluminium och en matt svart hård beläggning erbjuder denna monteringsplatta både hållbarhet och stil.
Specifikationer:
- Material: 7075 Aluminium
- Beläggning: Matt svart hård beläggning
- Totallängd: 1.780"
- Övergripande bredd: 1.1"
- Monteringshårdvara: (2) 6-32 Flat Head Skruvar, (1) 6-32 X 3/16 Set Skruv
- Rödpunktskompatibilitet: Trijicon RMR
Denna montering passar:
- Smith & Wesson M&P Full Size
- Smith & Wesson M&P 2.0 Full Size
- Smith & Wesson M&P 22 Full Size
- Smith & Wesson M&P Compact*
- Smith & Wesson M&P 2.0 Compact*
- Smith & Wesson SD9VE
- Smith & Wesson SD40VE
Denna montering passar inte:
- Smith & Wesson M&P Shield (Vår montering är för bred för att passa Shield)
- Smith & Wesson M&P Shield EZ .380
- Smith & Wesson SW9VE
- Smith & Wesson SW40VE
- Smith & Wesson M&P C.O.R.E Series
*Passar inte M&P .22 Compact. Smith and Wessons bakre sikt dovetails kan variera i dimensioner. Våra siktar är tillverkade för att uppfylla samma toleranser. Vissa användare kan ha problem med att installera vår platta på sin slide på grund av varierande toleranser. Tänk på detta när du beställer.
Dessa monteringar bör installeras och kontrolleras av en kvalificerad vapensmed. Ingen ansvarighet uttrycks eller antyds för skador eller skador som kan uppstå vid felaktig installation eller användning av denna produkt.
Installationsinstruktioner:
- Ta bort bakre sikt*
- Installera EGW Sight Mount i dovetailen
- Dra åt set skruven (om tillämpligt)
- Placera rödpunktsiktet på EGW Sight Mount (genom att placera en liten bit papper mellan rödpunktsiktet och siktfästet underlättar borttagning och håller Loctite borta från rödpunktsiktet.)
- Tillämpa blå Loctite på de medföljande monteringsskruvarna
- Dra åt monteringsskruvarna till 15in/lbs
*Bakre sikt pusher verktyg rekommenderas starkt